WARNING: You’ll need 4.5 minutes to endure my favourite snaps from our trip to Maputo / Pomene / Tofo / Bilene …
A billion is a difficult number to comprehend, but one advertising agency did a good job of putting that figure into some perspective in one of its press releases.
A. A billion seconds ago it was 1987.
B. A billion minutes ago Jesus was alive.
C. A billion hours ago our ancestors were living in the Stone Age.
D. A billion days ago no-one walked on the earth on two feet.
E. A billion Rand is spent in only 27 hours and 12 minutes, at the rate the SA government is spending it.
Okay, so you want more accurate numbers?
Assume it is now 29th January, 2016 at 8:46 PM.
1,000,000 seconds ago: 7:00 AM on 18th January
10,000,000 seconds ago: 3:00 AM on 6th October 2015 (115 days ago)
100,000,000 seconds ago: 12:00 PM on 28th November 2012 (3.17 years ago)
Billion and above:
1,000,000,000 seconds ago: 7:00 PM on 22nd May 1984 (31.69 years ago)
10,000,000,000 seconds ago: 3:00 AM on 13th March 1699 (316.88 years ago)
100,000,000,000 seconds ago: 27th March 1154 B.C. (3168.81 years ago)
1,000,000,000,000 seconds ago: 15 December 29674 B.C. (31,688.1 years ago)
P.S. The times (where mentioned) are accurate to an extremely high precision, give or take a minute, for most of the dates.
Law of Mechanical Repair
After your hands become coated with grease, your nose will begin to itch and you’ll need the toilet.
Law of Gravity
Any tool, nut, bolt, screw, when dropped, will roll to the least accessible place in the universe.
Law of Probability
The probability of being watched is directly proportional to the stupidity of your act.
Law of Random Numbers
If you dial a wrong number, you never get an engaged signal; someone always answers.
If you change lines in traffic, the one you were in will always move faster than the one you are in now.
Law of the Bath
When the body is fully immersed in water, the telephone will ring.
Law of Close Encounters
The probability of meeting someone you know INCREASES dramatically when you are with someone you don’t want to be seen with.
Law of the Result
When you try to prove to someone that a machine won’t work, IT WILL!!!
Law of Biomechanics
The severity of the itch is inversely proportional to the ease of reach.
The Coffee/Tea Law
As soon as you sit down to a cup of hot coffee or tea, your boss will ask you to do something which will last until the drink is cold.
Murphy’s= Law of Lockers
If there are only 2 people in a locker room, they will have adjacent lockers.
Law of Physical Surfaces
The chances of a slice of jam on bread landing face down on a floor are directly correlated to the newness and cost of the carpet or rug.
Law of Logical Argument
Anything is possible IF you don’t know what you are talking about.
Law of Physical Appearance
If the clothes fit, they’re ugly.
Law of Public Speaking
A CLOSED MOUTH GATHERS NO FEET!
Law of Commercial Marketing Strategy
As soon as you find a product that you really like, they will stop making it OR the store will stop selling it!
If you don’t feel well, make an appointment to go to the doctor, by the time you get there, you’ll feel better. But don’t make an appointment and you’ll stay sick.
The spectacular July 4 fireworks display you’re about to see was photographed by videographer Jos Stiglingh a year ago in Florida. He flew a DJI Phantom 2 quadcopter deep into the fireworks show and recorded it with an attached GoPro Hero 3 videocam.
The performance — or rather, the entire collection of performances — was high-risk for a flying camera passing inside all that explosive technology. We’re in considerably less danger watching this video version of the show.
What is a Rocket Stove?
- A rocket stove produces a very intense, very hot, smokeless flame using small amounts of wood
- A rocket stove is an efficient cooking stove using small diameter wood fuel which is burned in a simple high-temperature combustion chamber containing a vertical chimney, which ensures almost complete combustion prior to the flames reaching the cooking surface.
Why a Rocket Stove?
- It uses less fuel, therefore lower cost.
- It produces a very high heat output.
- It produces smoke only at the beginning.
- It reduces the exposure to indoor air pollution.
- It reduces lung, heart and eye problems.
- It reduces CO2 emissions and deforestation.
This video is less than 18 minute long and contains an amazing amount of detail. Thanks to Gene Lonergan.
by Douglas Barnes
The guidelines in this article are based on Art Ludwig’s industry-leading work.For further information on greywater systems, please refer to Ludwig’s Create an Oasis with Greywater, Branched Drain Greywater Systems, and Builder’s Greywater Guide. These are the best publications available regarding the construction of greywater systems.
Conservation of water is rightfully a growing concern throughout the world. Less than 2.6% of the water on the planet is freshwater. Of that, about 69.6% is locked away in ice and another 30.1% in groundwater, including 13.5% in deep groundwater reserves over 800 metres underground. Only 0.6% of the world’s freshwater is immediately available on the surface via lakes and rivers; and only 0.037% is in the atmosphere at any one time.
Industrial activity and industrial agriculture consume large amounts of the water that is available. And predictions for continental inlands forecast that global warming will bring drier conditions than those that currently exist. Of the total land mass of the Earth, 47.2% is arid, much of that converted to desert by human activity with a further 25% of the land at risk of desertification. And this problem is not limited to poor nations. While 66% of African lands suffer from desertification, 40% of the pastureland in Texas is now too arid for use. And pivot irrigation is turning patches of land on the Great Plains of North America into salted desert in 3 to 4 years. Even former patches of the Amazon rainforest are very close to becoming desert. Global water consumption is rising so fast that by 2025 demand will surpass availability by 56%. We need to shift to sustainable water usage, or we risk creating a planet largely comprised of desert.
One way to use water more efficiently, and return it to the environment clean is by greywater systems. Greywater is waste water from homes from sources excluding toilets. It is water from sinks and drains containing small amounts of nutrient-rich organic matter. Household waste water typically consists of 50 to 80% greywater. To flush this into a sewage system is a waste of life’s most precious resource.
Irrigation by spraying is very inefficient with up to 80% of the water evaporating. This has lead to severe salinisation and desertification in some areas. Greywater drained into mulch or leach pits, on the other hand, has almost no evaporation and results in about 40% of the water being taken up directly by plants (the remainder is filtered by soil microbes before tickling down to recharge groundwater systems).
Urban households can save the energy used to purify municipal water by not using tap water for watering plants. Rural households using pumps can reduce their energy and material needs by using greywater over well water for watering.
Utilising greywater also extends the life of septic systems or reduces the load on municipal sewage treatment plants. And in areas where septic tanks are less practical, such as clayey soils and rocky areas where septic fluids cannot trickle into the ground, greywater can help tackle waste water issues.
The use of greywater helps to recharge groundwater.
Good systems are cheap to build. (More expensive systems usually perform poorly.)
Greywater systems need a certain amount of space. Not every site has enough land for the water generated from the home. Partial sites from only one part (one sink, for example) may be all that can be tapped for a greywater site.
Very wet areas may become saturated with water. Such situations may be impractical or may require a different approach, such as greywater wetlands.
Cold climates make outdoor greywater systems possible through the warm season only.
Reduced water flow from a household can create a problem in urban areas with a municipal sewage system. It may be that the reduction in water flow through the pipes means that there is not enough flow to move toilet solids into the sewage main line.
Many building codes have a lot of catching up to do when it comes to greywater. A system can be built with a diverter to the currently approved (i.e. unsustainable) system. The diverter can then be used to flow water into the greywater system once the code changes. This system can also be used to deal with freezing conditions mentioned above.
Arid regions need carefully managed systems due to their inherent problems with salinity. Proper choice of detergents is important for every system but becomes vital in arid regions. It is a good idea to incorporate rainwater harvesting systems with greywater, particularly laundry greywater. First-flush and/or tank overflow can be connected to greywater drains to wash away excess salts.
An effective, safe greywater system slowly filters water through the soil so that microbes can devour the organic material in the water. The system should be designed such that people never come in contact with the greywater. The systems can be used to assist food production, provided that the plants arenot root crops. Don’t spray grey water on plants (or anything else). The water could contaminate the plant and contaminated water droplets could be inhaled.
As a safety precaution, purple pipes are used in the construction of greywater systems, if possible. This colour standard is to avoid any accidental consumption.
Don’t store greywater. It will fester dangerously. Also, design the system to keep water flowing. Systems that allow stagnation will convert relatively clean waste water into a health hazard.
It is a good idea to design the system with a 3-way diverter valve so that greywater can be either directed into the greywater system or to the sewage system. In cold climates, this feature is a necessity.
Make the system so that water sinks into the ground. Don’t allow greywater systems to flow into lakes or rivers, or you risk (illegally) contaminating them. A good rule of thumb is to keep systems at least 50 feet from open water. Local codes may require more than this. (To be fair to greywater systems, it should be noted that about 20% of sewage systems in the U.S. discharge sewage with only solids removed directly into natural open water; and all systems flush into water systems during heavy rains.)
Greywater systems require a change in behaviour. Harsh household chemical cleansers will have to be substituted for greener alternatives.
Consider the bedrock on the site. On a site with limestone, it is theoretically possible, however unlikely, to contaminate groundwater with a grey water system. Greywater systems are still possible, but the potential danger must be addressed in the design.
Avoid perforated pipes for water distribution. First, they clog with sediments from the greywater. Second, even water distribution from the holes is next to impossible. Third, roots will surely clog the system. Dumping directly into a gravel bed system or mulch pit is much better, is simpler to design, cheaper to build, and cheaper and easier to maintain.
Also avoid grease filters and other filtration systems. They will clog and they will clog quickly. If regular cleaning of messy and potentially toxic filters is a necessity of the system, it is likely that the user will stop using the system.
Greywater Volumes by Source:
|Washers||115 to 190 litres per day.||Good water quality.|
|Bath tubs||150 litres per use.||Good water quality.|
|Kitchen sink||20 to 60 litres per person per day.||Nutrient rich, but high in grease, soap and solids. Use drain screen.|
|Shower||40 litres per person per day.||Good quality. Use drain screen.|
|Dishwasher||20 to 40 litres per day.||Poor quality due to salt in dishwashing detergent.|
|Bathroom sinks||4 to 20 litres per person per day.||Good quality.|
Perhaps the simplest, cheapest, most reliable, best performing greywater system is the branched drain system emptying to mulch pits or leach fields, created by greywater master designer Art Ludwig. In this system, “double-elbow” pipe fittings are used to spread the flow of greywater to different areas of the garden. The branched drain system allows greywater to split into two paths up to 4 times. In other words, 16 drains to mulch pits or leach fields are possible in one branched system. Valves can be placed on each branch to allow that section’s flow to be cut off. The ideal place to do this is on the level section after each double elbow. This will prevent water from backing up and stagnating in the pipes.
The elbow will effectively halve the flow, but you will need to ensure that the pipe leading up to the elbow has at least 50 cm (about 20”) of straight section. Also, the slope of the pipes should be kept at a fall of 1:48 or steeper to keep the water flowing.
Whether a system is branched or not the ends can be hoses (flexible PVC is advisable as it does not look like a garden hose, thus people are unlikely to drink from it mistakenly), making them movable. This allows different areas to be watered. The advantage here is if one area becomes saturated, it can be shut off.
The “gravity drum” system is ideal for draining washing machines evenly without surges in flow. This system will either have to be branched as above to deliver to a number of sites, or its drainage hose will have to be moved to avoid one location from becoming saturated. Greywater flows from the washing machine’s drainage hose into the top of a 55 gallon plastic drum. At the bottom of the drum, a hole is drilled and a coupling is added to fit a hose to drain the drum as shown. It will be necessary to put a small hole in the top of the barrel, or water will siphon out preventing the machine from refilling (wasting water and making the machine inoperable until the siphon is broken).
Big-brand detergents can be very high in sodium, so it is best to choose a brand that has a low environmental impact. Only in tropical highlands would this extra sodium be beneficial, but only in small amounts. To address the sodium accumulation, it is best to combine the system with rainwater collection from the roof (or other surface as the case may be) to flush out the excess.
Greywater can simply be delivered into a mulch pit by placing the end of the pipe in the mulch. The diagrams below show a slightly more elaborate system that drain into a swale (a water-harvesting ditch on contour).
Leach fields are another simple and safe way to distribute greywater. The diagrams below demonstrate one method to construct a simple leach field. This design delivers simplicity and construction savings at the expense of a somewhat imprecise distribution of greywater.
A trench 1 to 2 meters long and 40 to 50 cm deep is dug and partially filled with gravel or mulch. A hole is cut in the bottom of a clay or plastic flower pot and the greywater hose fitted to it. It is best to push to hose through into the pot and place a coupler on the hose larger in diameter than the hole in the pot. This will prevent the hose from pulling out. Place the pot on the gravel, or if you use mulch, rest the pot on some bricks to keep the pot from sinking into the mulch. Then cover the rest with mulch. The diagram show the tops exposed, but they can be buried in mulch.
Straight greywater cannot be stored for long before it will stagnate and become a smelly health hazard. Once it is treated, however, the water can be held in tanks for later non-potable use. The design below illustrates a simple system using the technique just described to treat water that can be used downstream in the system. The entire unit can be built into a water proofed plywood box or a constructed ferro-cement box.
These leach fields are a convenient solution for cold climates. Outdoor greywater systems need to be shut down in winter as they would freeze up. Leach fields, however, can be incorporated into a greenhouse. Furthermore, any warmth from the use of hot water can be transferred to a greenhouse rather than wasted in the septic or sewage system.
Another option for the treatment of greywater that lends itself well to greenhouses is the constructed wetland. This system is also an option for very wet areas where the ground is too saturated to accept additions of greywater. The water exiting the constructed wetland could be used for irrigation purposes or could go into an aquaculture system. One square foot of wetland surface area will be enough to treat one gallon of water. So, if you produce 50 gallons from one source, you will need 50 square feet of wetland surface area. The fine tuning of these systems can be a bit tricky as nutrient supply determines how many plants can survive. If the system is in a greenhouse, it will be simpler as you do not need to consider the amount of rainfall you can expect to receive. And if the system is too big for the nutrient supply, this can be remedied by controlled additions of actively aerated compost tea.
If your system is to drain outdoors, you will need to check if your soil is capable of handling the load. Dig a 30 cm (12”) deep hole about 10 or 15 cm in diameter. Fill the hole with water 2 or 3 times to saturate the soil. Then place a stake with marks denoting distance (in inches or centimetres) in the hole. Fill the hole with water and time how long it takes for the water to drain down. It will give you the inches or centimetres per minute that the soil is capable of handling.
If you are building a new home, do not mix greywater pipes with blackwater (from the toilet) pipes, including the vents. This makes implementing a greywater system easier. Also, implementation will be easier if you design your greywater pipes to conserve vertical drop as the system will be gravity fed.
Use between 2 inch and 1 ½ inch pipes. Any smaller and clogs are more likely. Any larger and solids might stick on the bottom of the pipe.
Be careful to keep the slope of all the pipes in the system at least 1:48 (1 cm drop over 48 cm, or ¼” drop over one foot) or steeper. And less and you risk clogs forming in the system. Also design the final outlet to empty the water with a fall of several inches. This will prevent solids from backing up at the end of the pipe and clogging.
Map out the system for future maintenance, and be sure to incorporate easily accessible cleanouts.
There’s been no news since November 2014 because….
…our builder Patrick O’ Neill from PM Roofrooms appears to have absconded. After many delays over the past 9 months completion was promised by the end of February 2015. No builder has been on site since the beginning of February. Patrick has not replied to any communications since the end of February.
Considerable work is still outstanding!
Status of the building as at 15 March 2015
Noisy Floor Beams
- The builder, Patrick O’ Neill of PM Roofrooms, the beam manufacturer, Patrick Swanepoel of the Hazycrest Group, and the engineer, Ian Upton agreed that the beams were abnormally noisy.
- Various solutions were suggested by them
- Patrick Swanepoel did some experimental changes to some beams in situ.
- Patrick O’ Neill and Patrick Swanepoel dispute who is responsible for correcting the fault and no repairs have been done.
- Floor boards have been lifted to expose faulty beams.
- This fault has delayed work on the building since September 2014
Stairs and Landing
Skimming of External Walls
Work site not cleaned up
|Architect:||Bryan Lee from Lee Sanders Architects|
|Builder:||Patrick O’ Neill from PM Roofrooms|
|Steel Beam Manufacturer:||Patrick Swanepoel from Hazycrest Group|
|Plumber:||Renier van der Merwe from Eco Wise Plumbing|
|Electrician:||Deon van Dyk from Deon’s Electrical|
A hike through Spain‘s El Caminito del Rey (“The King’s Little Pathway”) is not for the faint of heart. In fact, the narrow pathways, incredible height, and sharp rocks below are the stuff of nightmares. I don’t know how the person filmed and walked at the same time.